On a coated auxiliary plate, the around about 4 cm higher than the ground, tighten it with two clamps. The two short edge bands are aligned to match the floor and fixed with small clamps. Then you can adjust the long edge band and glue it to the floor. It lies flat to the ground, but is above 4 mm about. If you then cut off the back corners of the floors at a 45 degree angle, you can add glue and tighten the short pre-gluers.
You also have to create a working aid for slitting the glued door frames, so that you can guide the corners upright over the circular saw. Simply chisel out the wooden bridge between the saw cuts with a narrow chisel, glue in the solid wood spring. by the way: Mill all decorative profiles first, after the edge bands are glued to the floors. This makes handling the table router easier. And the surface treatment of the wood is best done by you, even before you glue the body.
8 A cutting box, made of frame wood- and leftovers glued together, Do you need, to saw in the corners of the envelope twice.
9 An auxiliary plate, inserted tightly into the glass fold of the frame, prevented, that the wood bends when the bevel is adjusted.
10 milling profiles: perfect with the router in the router table. Start at the corner on the right, mill outwards. Continue like this in segments.
11 A cutter, four profiles, you can do that too! From the left: Glass molding, door frame profile, profile upper, Subfloor and shelf profile.
12 Liquid wood wax, applied with a cloth before gluing, protects the wood and accentuates the grain. Brushing brings shine.
13 The disc, placed in the rebate on the back of the door, is held by glazing beads and brass pins. Run the hammer on the disc.
14 Three servants with me 100 cm span as well as two auxiliary panels tailored to the shape of the floors as extras, to glue the body. The auxiliary plates distribute the pressure of the clamps to all dowels.
DESIGN TIP YOUR CHOICE OF SURFACES
This is how you can integrate a worktop into the system, brown oak, limed oak: These are just three examples of many, how to treat the surface of your cupboard with commercially available stains or stains. with a pore filler (by clou) can refine. Before treating, you should soak the material and sand it fine.
Nr. Part Number Material Length Width Thickness
1 page 1 carpenter. oak veneer. 760 415 19
2 page 1 carpenter. oak veneer. 760 400* 19
3 Side parts from 2 carpenter. oak veneer. 760 100 19
4 Subsoil/topsoil 1 carpenter. oak veneer. 650* 390 19
5 Shelves 1 (2) carpenter. oak veneer. 600* 330* 19
6 Frame wooden door 2 Oak solid wood 800 50 23
7 Frame wooden door 2 Oak solid wood 500 50 23
8 Glue base/lid 1,8 lfd.m. Oak solid wood 23 23
9 Gluing Up. front 2 Oak solid wood 800 20 23
10 Glued shelf 1 (2) Solid oak wood each 550 20 10
11 Springs for door corners 4 Oak solid wood, vote on slots
12 The glass molding 2,2 running meter solid oak wood 12 9
13 Dowels 24 beech 35(40) ∅10
14 Slice of glass, cut after finished door 3
15 Hinges 2 Polished brass 50 50 ***
16 Knopf 1 Polished brass
17 Floor support 4 (8) Brass-plated steel ∅ 5,5
18 Pins for glazing beads 16 Brass plated steel 20 ∅1,2
19 Hinge screws 12 Messing 3 x 16
20 threaded screw 1 Messing 30 M4
21 Magnetic catch 1 Stahl
*) Dimensions include allowance for fitting cut, all information in mm
**) Adjust the cross section to the rebate size
***) with. B. Make ONI No. 042553 or ROBBI No. 00821 – specialist trade